The short answer
A heat pump replaces a separate furnace and air conditioner with one electric system. In San Leandro we size it to your house, check your ducts and electrical panel, and help you confirm current incentives. You don't have to replace a working furnace, but gas furnaces manufactured from 2029 face a zero-NOx standard.
If you're replacing an aging furnace or want to add cooling to your San Leandro home, a heat pump can heat and cool with one system. ExpertFlow HVAC Repair Service installs heat pumps for homeowners in the 94577, 94578 and 94579 ZIP codes, about 16 miles west of our base in Pleasanton. Below we explain how we plan and size a system for your house, what Bay Area Air District rules mean for your timing, and how to check current incentives before you commit.
Why San Leandro Homeowners Are Considering Heat Pumps
A heat pump moves heat instead of burning fuel. In winter it pulls heat from outdoor air and brings it inside. In summer it runs in reverse and moves heat out of the house. If your home has a gas furnace and no central air, a heat pump can add cooling without a separate air conditioner.
Local rules matter for timing. Under Bay Area Air District Rule 9-4, natural gas furnaces manufactured from 2029 must meet a zero-NOx emission standard. In practice, that points homeowners toward heat pumps when they replace a furnace after that date. The rule does not force you to replace equipment that still works. It applies only when your existing furnace fails or is replaced. Many people plan the switch before their furnace gives out, so they aren't choosing a system in a hurry on a cold night.
How We Plan Your Installation
Every heat pump job starts with a visit to your house. We don't size a system by matching the old furnace. An oversized heat pump cycles on and off too often. An undersized one runs constantly and struggles on the coldest and hottest days. Before we recommend equipment, we look at:
- Heating and cooling load, based on square footage, insulation, windows and which way the house faces
- Condition, sizing and sealing of your existing ductwork
- Electrical panel capacity and whether the system needs a new circuit
- Where the outdoor unit can go, with attention to airflow, noise and clearance from neighbors
- Thermostat compatibility and how you want to control the temperature
Ducted and Ductless Options
If your home already has ducts in good shape, a ducted heat pump can often connect to them. It replaces the furnace's air handler and adds an outdoor unit. You keep the same supply and return vents, and every room you heat now also gets cooling.
Homes without ductwork, or with additions, converted garages or rooms that never stay comfortable, may suit ductless mini-splits better. These use small indoor heads mounted on the wall, linked by refrigerant lines to an outdoor unit. Some homes use both: a ducted system for the main house and a mini-split for the room the ducts don't reach well. We'll lay out the tradeoffs for your floor plan rather than pushing one approach.
Incentives and Tax Credits: What's Current
The federal Energy Efficient Home Improvement Credit (25C) covered qualifying heat pumps placed in service before December 31, 2025. It is not available for new installations after that date, so don't count on it in your budget.
Bay Area homeowners can still check BayREN and their local clean energy provider for heat pump and electrification incentives. Amounts and availability change with each funding cycle, so we confirm the current offer before we include it in a quote.
If you're also thinking about a heat pump water heater, the zero-NOx date for small water heaters under Rule 9-6 was set for 2027. The Air District Board is considering amendments in November 2026 that could delay it. Check the current rule before you plan a water heater replacement.
What to Expect on Installation Day
Once you approve the plan, we schedule the work and walk you through each step. A typical ducted replacement includes:
- Protecting floors and work areas, then safely disconnecting the old equipment
- Setting the outdoor unit on a level pad or bracket
- Installing the indoor air handler or coil and connecting it to your ducts
- Running refrigerant lines, condensate drainage and electrical connections
- Testing airflow, refrigerant charge and both heating and cooling modes
- Showing you how to use the thermostat and when to change filters
Serving San Leandro and Nearby Communities
Along with San Leandro, we install heat pumps in Hayward, Union City, San Ramon, Danville and Moraga. If you live in one of those areas, the same planning and sizing process applies to your home.
More services in San Leandro
- AC Repair in San Leandro
- Heating Repair in San Leandro
- AC Installation in San Leandro
- Furnace Repair in San Leandro

